Engineering » Page 9

Engineering

Jair Larson

Which is not a job in Manufacturing?

A.

Industrial production manager

B.

Quality control inspector

C.

Software developer

D.

Painting and coating worker

Answer Answers (1)

Engineering

Brynn Jordan

Why is there a ring of satellites around the Earth's equator roughly 22,000 miles away from the Earth?

Answer Answers (1)

Engineering

Savion Allison

A specimen has circular cross-sectional area with initial diameter d = 26 mm and a gauge length Lo = 200 mm. A force P = 127 kN elongates the specimen by delta = 3 x 10^-1 mm. The specimen material has yielding strength σy = 350 MPa and shear modulus G = 66 GPa. % Determine the Poisson ratio

Answer Answers (1)

Engineering

Joselyn Bonilla

A car air-conditioning unit has a 0.5-kg aluminum storage cylinder that is sealed with a valve, and itcontains 2 L of refrigerant R1 34a at 500 kPa; bothare at room temperature 20'C./t is now installedin a car sitting outdoors, where the whole systemcools do,"vn to the ambient temperature of - 10"C. What is the irreversibility of this process?

Answer Answers (1)

Engineering

Jessica Mercer

In a Series circuit with two identical loads, the voltage across each load will be:

A. the same

B. 12V each

C. higher on the first load in the circuit

D. dependent on the current rating of the loads

Answer Answers (1)

Engineering

Abbie

What is the purpose of a hash function? Choice a To provide integrity Choice b To create a value that cannot be repudiated by its sender Choice c To obfuscate a data segment such that it cannot be deciphered without a key Choice d To preserve a copy of all of the information from the original data segment

Answer Answers (1)

Engineering

Genevieve Patton

What engine does the Lexus is300 have?

Answer Answers (1)

Engineering

Scott Robinson

Two physical properties that have a major influence on the cracking of workpieces, tools, or dies during thermal cycling are thermal conductivity and thermal expansion. Explain why.

Answer Answers (1)

Engineering

Dixie Adams

9.17 LAB: Name format Many documents use a specific format for a person's name. Write a program whose input is: firstName middleName lastName, and whose output is: lastName, firstName middleInitial. Ex: If the input is: Pat Silly Doe the output is: Doe, Pat S. If the input has the form firstName lastName, the output is lastName, firstName. Ex: If the input is: Julia Clark the output is: Clark, Julia

Answer Answers (1)

Engineering

Omari Davila

Air, modeled as an ideal gas, is compresses at steady state from 1 bar, 300 K, to 5 bar, 500K, with 150 kW of power input. Heat transfer occurs at a rate of 20 kW fom the air to cooling water circulating in a water jacket enclosing the compressor. Neglecting kinetic energy and potential energy effects, determine the mass flow rate of the air, in kg/s.

Answer Answers (1)

Engineering

Zayden Moses

Large side-to-side differences in SAI or included angle could

indicate what?

O A) Underinflated tires

O B) Loose steering gear mounts

O C) Tight ball joints

O D) A possible bent component

Answer Answers (1)

Engineering

Ellen Arroyo

The mechanical properties of a metal may be improved by incorporating fine particles of its oxide. Given that the moduli of elasticity of the metal and oxide are, respectively, 60 GPa and 380 GPa, what is the (a) upper-bound, and (b) lower-bound modulus of elasticity values (in GPa) for a composite that has a composition of 33 vol% of oxide particles.

Answer Answers (1)

Engineering

Katherine Forbes

You are using a Geiger counter to measure the activity of a radioactive substance over the course of several minutes. If the reading of 400. counts has diminished to 100. counts after 66.7 minutes, what is the half-life of this substance? Express your answer with the appropriate units.

Answer Answers (1)

Engineering

Angelo Mendez

Justify with proper description why low cost automation is required to improve productivity in small scale

industries. List out some examples.

Answer Answers (1)

Engineering

Vivian Blevins

A particular op amp using ±15-V supplies operates linearly for outputs in the range-14 V to+14 V. If used in an inverting amplifier configuration of gain - 100, what is the rms value of the largest possible sine wave that can be applied at the input without output clipping?

Answer Answers (1)