Ask Question
EngineeringEngineering
14 October, 19:41

A gas flows through a one-inlet, one-exit control volume operating at steady state. Heat transfer at the rate takes place only at a location on the boundary where the temperature is Tb. For each of the following cases, determine whether the specific entropy of the gas at the exit is greater than, equal to, or less than the specific entropy of the gas at the inlet:

(a) No internal irreversibilities,

(b) no internal irreversibilities,

(c) no internal irreversibilities,

(d) internal irreversibilities,

(e) internal irreversibilities.

+4
Answers (1)
  1. 14 October, 22:31
    0
    (a) S₁-S₂ = 0 ⇒ S₁=S₂ (b) S₁-S₂<0 ⇒ S₁0 ⇒ S₁>S₂ (d) S₁-S₂>0 ⇒ S₁>S₂

    Explanation:

    Solution

    Now,

    From the entropy rate balance at steady state, the equation is stated below:

    Qcv = / Tb + m (S₁-S₂) + σcv = 0

    ΔS = Qcv/Tb + σcv

    So,

    S₁-S₂ = Qcv/mTb + σcv/m

    (a) No internal irreversibilities and Q cv = 0

    Now,

    If Qcv = 0, the and value of σcv = 0

    S₁-S₂ = (Qcv/mTb + σcv/m) = 0

    hence

    S₁-S₂ = 0 which is S₁=S₂

    (b) no internal irreversibilities, and Q cv <0

    If Q cv <0 the value becomes this,

    S₁-S₂ = (Qcv/mTb + σcv/m) <0

    So,

    S₁-S₂<0 which is S₁
    (c) no internal irreversibilities and Q cv >0

    If Q cv >0 the value is

    S₁-S₂ = (Qcv/mTb + σcv/m) >0

    So,

    S₁-S₂>0 which is S₁>S₂

    (d) internal irreversibilities and Qcv ≥ 0

    If Q cv ≥0 the value is

    S₁-S₂ = (Qcv/mTb + σcv/m) >0

    So,

    S₁-S₂>0 which is S₁>S₂

    Note: option (d) and (e) are the same
Know the Answer?
Not Sure About the Answer?
Find an answer to your question ✅ “A gas flows through a one-inlet, one-exit control volume operating at steady state. Heat transfer at the rate takes place only at a ...” in 📘 Engineering if you're in doubt about the correctness of the answers or there's no answer, then try to use the smart search and find answers to the similar questions.
Search for Other Answers
You Might be Interested in
How much to build a barber clipper?
Answers (1)
Which of the following vehicles has no emissions?
Answers (1)
1. The AWS A5.5 is a list of electrodes used to weld which type of metal? A Copper and copper alloys. B. Carbon steels. C. Low alloy steels. D. Gray and ductile iron. E. Corrosion-resistant steels.
Answers (1)
Which term describes the top or bottom component of a trussed beam
Answers (1)
The yield strength for an alloy that has an average grain diameter of 5.3 x 10-2 mm is 121 MPa. At a grain diameter of 8.0 x 10-3 mm, the yield strength increases to 233 MPa. At what grain diameter, in mm, will the yield strength be 209 MPa?
Answers (1)
New Questions in Engineering
How many watts of power are used in a circuit with a 1.5V battery drawiing 410 mA?
Answers (1)
Brian is responsible for ordering cement for a construction project. He had just determined that the construction crew would need 540 cubic yards of cement when the building owner decided to shorten the driveway, eliminating the need for 44 cubic
Answers (2)
Dave is a recruiter for a very large graphic design firm and he is looking for an employee who is willing to give the entire productive hours to activities related to the job. Which quality is he looking for?
Answers (2)
Which of the following is a common use for commas? Separating two elements Separating unrelated adjectives Connecting two independent clauses Connecting two dependent clauses
Answers (2)
Which component stores energy as potential energy in a mechanical system?
Answers (1)
Home » Engineering » A gas flows through a one-inlet, one-exit control volume operating at steady state. Heat transfer at the rate takes place only at a location on the boundary where the temperature is Tb.
Sign Up Forgot Password?